Maagizo ya Paneli ya Kiraka cha VOID D1 Plus

KUMBUKA YA MAOMBI

Jopo la Kiraka la D1 Plus

Wiring the Bias D1+/Q1+/Q1.5+/Q2+ Patch Panel
Upendeleo wa Void Acoustics' D1+/Q1+/Q1.5+/Q2+ hutumia muunganisho wa mtindo wa phoenix kwa maingizo na matokeo ya sauti ya analogi. Unapokuwa katika mazingira ya kutembelea ambapo kuweka upya waya amplifier mara kwa mara inaweza kuhitajika, miunganisho ya kawaida kama vile XLR na speakON inafaa zaidi.

Paneli ya Upendeleo iliyoonyeshwa kwenye Mchoro wa 1 huruhusu muunganisho unaotaka wa XLR na speakON huku ukitumia Upendeleo D1+/Q1+/Q1.5+/Q2+ ampmaisha zaidi.
The wires are pre-terminated with bootlace ferrules for easy set up.
The ground/shield wires for the Input signal connections have a green heat- shrink applied. This is a thicker wire than the green signal wire used for Ch3.
Mwongozo ufuatao unaonyesha jinsi ya kuunganisha paneli ya kiraka kwa Bias+ amplifiers ikiwa ni pamoja na matoleo yasiyo ya pamoja ya Upendeleo.

Wiring kwa Bias D1+

Jopo la Kiraka la Upendeleo linaweza kutumika kufanya kazi na Upendeleo D1+ mbili ampwaokoaji.
The following method puts one amplifier kwenye Ingizo/Zao 1+2 na nyingine kwenye Ingizo/Mito 3+4. Ikiwa wiring kwa moja amplifier, ruka hatua zinazorejelea sekunde ampmaisha zaidi.
Ishara ya Kuingiza
The Bias D1+ has two inputs, therefore the third and fourth inputs on the patch panel can be used for a second D1+ ampmaisha zaidi.

Wakati wa kuunganisha sehemu ya pili ya Upendeleo D1+ kwenye paneli ya Kiraka cha Upendeleo, feniksi ya ingizo ina waya kama ilivyo kwenye Mchoro 3.

Mawimbi ya Pato
There are two glands on the rear of the patch panel which have a 4×2.5mm cable. This cable is wired to the output phoenix connector. The labels on the cables will show 1+2/2 and 3+4/4.
If wiring two Bias D1+ amplifiers kwenye paneli ya kiraka, unganisha viunganishi vyote viwili kama ilivyo kwenye Mchoro 4 na Ch3 badala ya Ch1 na Ch4 badala ya Ch2.   Wakati wa kuchomeka kizuizi cha Phoenix cha kutoa kwenye Bias D1+, kitageuzwa skurubu upande chini na kuchomekwa kwenye Towe la Phoenix.

Wiring kwa Upendeleo Q1+/Q1.5+/Q2+

Ishara ya Kuingiza
The Gland on the right-hand side of the patch panel when looking at the rear, has 4 balanced cables within a multicore. The cables are individually labeled 1/A, 2/B, 3/C, 4/D. They are respectively Ch1, Ch2, Ch3, Ch4. They are wired as in Figure 5.

Wakati wa kuunganisha kwenye amplifier hakikisha kuwa unatumia muunganisho wa chini wa Ingizo wa Phoenix kama ilivyoangaziwa kwenye Mchoro 6.

Mawimbi ya Pato
There are two glands on the rear of the patch panel which each have a 4×2.5mm cable. This cable is wired to the output phoenix connector.
The labels on the cables will show 1+2/2 and 3+4/4. They are wired as in Figure 7. It is important to note the orientation of the phoenix block. Wakati wa kuchomeka kizuizi cha Phoenix cha kutoa kwenye Bias Q1+/Q1.5+/ Q2+, kitageuzwa skurubu upande chini na kuchomekwa kwenye Towe la Phoenix iliyoonyeshwa kwenye Mchoro 8.

Habari hii inaweza kubadilika bila taarifa.
Kwa toleo jipya zaidi la mtandaoni, tembelea: voidacoustics.com
© 2025 Void Acoustics Research Ltd.