SwitchBot W8200000 Sensorer ya Uwepo
Tafadhali soma mwongozo huu wa mtumiaji kwa uangalifu kabla ya kutumia kifaa chako. https://www.switch-bot.com/pages/switchbot-user-manual.
Yaliyomo kwenye Kifurushi
Orodha ya Vipengele
Maandalizi
Utahitaji:
- Simu mahiri au kompyuta kibao inayotumia Bluetooth 4.2 au toleo jipya zaidi.
- Toleo jipya zaidi la programu yetu, linaloweza kupakuliwa kupitia Apple App Store au Google Play Store.
- Akaunti ya SwitchBot, unaweza kujiandikisha kupitia programu yetu au kuingia katika akaunti yako moja kwa moja ikiwa tayari unayo.
- Please note: if you intend to use the third-party services or voice control, you will need a SwitchBot Hub (sold separately).
Mahitaji ya mfumo wa iOS na Android: https://support.switch-bot.com/hc/en-us/articles /12567397397271
Taarifa za Usalama
- Ondoa betri wakati haijatumiwa kwa muda mrefu.
- Usijaribu kutenganisha, kutengeneza, au kurekebisha kifaa.
- Tumia tu aina ya betri zilizoainishwa katika mwongozo huu.
Ufungaji
- Sakinisha betri
- Open the battery cover, insert two AAA batteries following the ” + ” and ” -” signs. Then close the battery cover and press it down until it clicks into place.
Add the device to the app
- Fungua programu ya SwitchBot na uingie.
- ap the ” +” icon at the top right of the home page. Find the Presence Sensor icon and select, then follow the instructions to complete the setup.
Masafa ya Ugunduzi
Sensorer ya Mwanga
Light sensor senses whether it is bright or dark in the target environment. For more information, please navigate to the Settings page of Presence Sensor in the app.
Jinsi ya Kutumia
Weka Upya Kitufe Kinachotazama Juu
- For accurate detection, position the sensor at chest height, aligned with your typical posture (sitting or standing). If installed higher, tilt it downward to target chest level.
Tafadhali kumbuka:
- Installing the Sensor too high or too low may reduce detection accuracy.
- Strictly follow the app’s installation and configuration guidelines to ensure proper detection performance.
Weka Upya Kitufe Kinachotazama Chini (kwa Wamiliki Wapenzi)
- If you are a pet owner, it is recommended to install the Sensor 0.1 to 0.2 m (3.9 to 7.9 in.) higher than your pet(s) with the Reset Button facing down, to prevent false alarms triggered by your pets.
Uwekaji
Without Base Place Presence Sensor directly on a table or shelf or stick it to a flat surface using the 3M double-sided adhesive tape.
Note: Make sure the lens is facing towards the desired area to be detected and close to the edge of the table or shelf to avoid blockage.
With Base Mount the Base on the back or bottom of Presence Sensor. The Base can be attached to a metal surface or a magnet.
You can also stick the base to a flat surface using the 3М double-sided adhesive tape. After Presence Sensor is properly installed, tilt it to a desired angle.
Note: Make sure the lens is facing towards the desired area to be detected and close to the edge of the table or shelf to avoid blockage.
Vidokezo vya Kuweka Mkanda wa Wambiso
- Ensure the target surface is dry and clean.
- Apply pressure to the Presence Sensor / Base for 60 seconds after installation.
- Keep away from heat sources (e.g., light bulbs).
Mwanga wa Kiashiria cha LED
Ubadilishaji wa Betri
Open the battery cover, remove the old batteries and insert two new AAA batteries following the ” +” and “-” signs. Then close the battery cover and press it down until it clicks into place.
Inarejesha kwa Mipangilio ya Kiwanda
Press and hold the Reset button for 15 seconds while the LED indicator light keeps flashing. Then, the light will stay lit for 1 second and turn off. Please Note: Resetting the device will restore all settings to their default values and clear all logs.
Kuboresha Firmware
Ili kuboresha matumizi ya mtumiaji, tutatoa masasisho ya programu dhibiti mara kwa mara ili kuanzisha vitendakazi vipya na kutatua hitilafu zozote za programu zinazoweza kutokea wakati wa matumizi. Toleo jipya la programu dhibiti linapatikana, tutakutumia arifa ya kuboresha akaunti yako kupitia programu yetu. Unaposasisha, tafadhali hakikisha kuwa bidhaa yako ina betri ya kutosha au uendelee kuwashwa na uhakikishe kuwa simu mahiri yako iko ndani ya masafa ili kuzuia usumbufu.
Kutatua matatizo
Tafadhali tembelea yetu webtovuti au changanua msimbo wa QR hapa chini kwa maelezo zaidi. https://support.switch-bot.com/hc/en-us/
categories 32315323860887
Vipimo
- Nyenzo: ABS
- Ukubwa:
- Presence Sensor: 54 × 54 × 30 mm (2.1 x 2.1 x 1.2 in.)
- Base: 45 × 45 × 32 mm (1.8 x 1.8 x 1.3 in.)
- Uzito: 19 g (oz. 0.7)
- Betri: AAA × 2
- Maisha ya Betri: Takriban. miaka 2
- Halijoto ya Kuendesha: 0°C hadi 40°C (32°F hadi 104°F)
- Unyevu wa Uendeshaji: 10% hadi 90% RH
- Muunganisho: Bluetooth 4.2
Udhamini
- Tunatoa uthibitisho kwa mmiliki halisi wa bidhaa kwamba bidhaa haitakuwa na kasoro katika nyenzo na uundaji. Tafadhali kumbuka kuwa dhamana hii ndogo haijumuishi:
- Bidhaa zilizowasilishwa zaidi ya kipindi cha awali cha dhamana.
- Bidhaa ambazo ukarabati au marekebisho yamejaribiwa.
- Bidhaa zinazoathiriwa na kuanguka, halijoto kali, maji au hali nyingine za uendeshaji nje ya vipimo vya bidhaa.
- Uharibifu unaotokana na maafa ya asili (ikiwa ni pamoja na lakini sio tu kwa umeme, mafuriko, kimbunga, tetemeko la ardhi, au kimbunga, n.k.).
- Uharibifu unaotokana na matumizi mabaya, unyanyasaji, uzembe au majeruhi (km moto).
- Uharibifu mwingine ambao hauhusiani na kasoro katika utengenezaji wa vifaa vya bidhaa.
- Bidhaa zilizonunuliwa kutoka kwa wauzaji wasioidhinishwa.
- Sehemu zinazotumika (pamoja na lakini sio tu kwa betri).
- Mavazi ya asili ya bidhaa.
Wasiliana na Usaidizi
- Maoni: Ikiwa una wasiwasi au matatizo yoyote unapotumia bidhaa zetu, tafadhali tuma maoni kupitia programu yetu kupitia Profile > Ukurasa wa usaidizi.
- Kuanzisha na kutatua matatizo: support.switch-bot.com
- Barua pepe ya Usaidizi: support@switch-bot.com
- www.switch-bot.com
- V1.02506|
Nyaraka / Rasilimali
 |
SwitchBot W8200000 Sensorer ya Uwepo [pdf] Mwongozo wa Mtumiaji Sensorer ya Uwepo ya W8200000, W8200000, Kihisi cha Uwepo, Kihisi |