M5Stack C6LoRA Module User Manual

M5Stamp C6LORA
Model: Stamp C6LoRA
Mwongozo wa Mtumiaji

Maelezo

Stamp C6LoRa is a high-performance programmable LoRa module designed for the 830 ~ 930 MHz frequency range. The module features an ESP32-C6 SoC, an SX1262 LoRa RF transceiver, and an LNA signal amplifier chip. It comes with two onboard IPEX antenna connectors for external Wi-Fi and LoRa antennas, respectively.
At its core, the ESP32-C6 integrates a rich set of peripheral interfaces, enabling extended functionality through secondary development. It also supports 2.4GHz Wi-Fi 6, offering broader possibilities for IoT applications. Additionally, the module includes a  PI4IOE5V6408 IO expander chip, which is used for LoRa transceiver circuit control and amplifier enable signal management, delivering enhanced power efficiency and providing additional usable IO resources.
A built-in DC-DC converter supports a DC input range of 3.7 to 5V and allows for lithium battery power, making it adaptable to various hardware deployment scenarios. The module is well-suited for long-range communication applications such as smart irrigation, remote metering, and power equipment control.

Vipimo

Anza Haraka

3.1 Maandalizi

1. Tembelea Arduino rasmi webtovuti na usakinishe IDE ya Arduino
   https://www.arduino.cc/en/Main/Software
2. Ongeza Meneja wa Bodi afuatayo URL kwa File → Mapendeleo → Kidhibiti cha Bodi za Ziada URLs:
   https://espressif.github.io/arduino-esp32/package_esp32_dev_index.json
3. Fungua Kidhibiti cha Bodi, tafuta "ESP32", na ubofye kusakinisha.
4. After installation, select the board “ESP32C6 Dev Module.”
5. Configure the following options. USB CDC On Boot: “Enabled”

3.2 Jaribio la Wi-Fi
Chagua exampna programu "Kutamples” → “WiFi” → “WiFiScan”, choose the port corresponding to your device, and click the compile and upload button in the top-left corner.
Baada ya upakiaji kukamilika, fungua Kifuatiliaji cha Ufuatiliaji kwa view Maelezo ya kuchanganua Wi-Fi.

3.3 BLE Scan
Chagua exampna programu "Kutamples” → “BLE” → ”Scan”, choose the port corresponding to your device, and click the compile and upload button in the top-left corner.
Baada ya upakiaji kukamilika, fungua Kifuatiliaji cha Ufuatiliaji kwa view BLE Scan habari.

3.4 LoRa TX
After burning the LoRa test firmware, check the LoRa transceiver information via the ESP32-C6 USB CDC serial port.

Onyo la FCC

Tahadhari ya FCC:
Mabadiliko yoyote au marekebisho ambayo hayajaidhinishwa waziwazi na mhusika anayehusika na utiifu yanaweza kubatilisha mamlaka ya mtumiaji kuendesha kifaa.
Kifaa hiki kinatii sehemu ya 15 ya Sheria za FCC. Uendeshaji unategemea masharti mawili yafuatayo: (1) Kifaa hiki hakiwezi kusababisha mwingiliano unaodhuru, na (2) kifaa hiki lazima kikubali uingiliaji wowote uliopokewa, ikiwa ni pamoja na kuingiliwa kunaweza kusababisha uendeshaji usiohitajika.

KUMBUKA MUHIMU:
Kumbuka: Kifaa hiki kimejaribiwa na kupatikana kuwa kinatii vikomo vya kifaa cha kidijitali cha Hatari B, kwa mujibu wa sehemu ya 15 ya Sheria za FCC. Vikomo hivi vimeundwa ili kutoa ulinzi unaofaa dhidi ya kuingiliwa kwa hatari katika usakinishaji wa makazi. Kifaa hiki huzalisha, kutumia, na kuangazia nishati ya masafa ya redio na, ikiwa hakijasakinishwa na kutumiwa kwa mujibu wa maagizo, kinaweza kusababisha mwingiliano unaodhuru kwa mawasiliano ya redio. Hata hivyo, hakuna uhakika kwamba kuingiliwa haitatokea katika ufungaji fulani. Ikiwa kifaa hiki kitasababisha usumbufu unaodhuru kwa upokeaji wa redio au televisheni, ambao unaweza kubainishwa kwa kuzima na kuwasha kifaa, mtumiaji anahimizwa kujaribu kusahihisha uingiliaji huo kwa moja au zaidi ya hatua zifuatazo:

• Elekeza upya au uhamishe tena antena inayopokea.
• Kuongeza utengano kati ya kifaa na mpokeaji.
• Unganisha vifaa kwenye plagi kwenye mzunguko tofauti na ile ambayo mpokeaji ameunganishwa.
• Wasiliana na muuzaji au mtaalamu wa redio/TV kwa usaidizi.

Taarifa ya Mionzi ya Mionzi ya FCC: Vifaa hivi vinafuata mipaka ya mfiduo wa mionzi ya FCC iliyowekwa kwa mazingira yasiyodhibitiwa.

Kumbuka Muhimu:
Katika tukio ambalo hali hizi haziwezi kufikiwa (kwa mfanoample, certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid, and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.

Maliza Uwekaji lebo kwenye Bidhaa
The final end product must be labeled in a visible area with the following “Contains FCC ID: 2AN3WM5STAMPC6LORA”.

Taarifa Mwongozo kwa Mtumiaji wa Mwisho
Kiunganishi cha OEM kinapaswa kufahamu kutotoa taarifa kwa mtumiaji wa mwisho kuhusu jinsi ya kusakinisha au kuondoa moduli hii ya RF katika mwongozo wa mtumiaji wa bidhaa ya mwisho inayounganisha sehemu hii.
Mwongozo wa mtumiaji wa mwisho utajumuisha taarifa/maonyo yote ya udhibiti kama inavyoonyeshwa katika mwongozo huu.

Maagizo ya ujumuishaji kwa watengenezaji wa bidhaa mwenyeji kulingana na Mwongozo wa KDB 996369 D03 OEM v01

2.2 Orodha ya sheria zinazotumika za FCC
CFR 47 FCC SEHEMU YA 15 SEHEMU NDOGO C imechunguzwa. Inatumika kwa transmita ya kawaida.

2.3 Masharti mahususi ya matumizi ya uendeshaji
Moduli hii ni moduli ya kusimama pekee. Ikiwa bidhaa ya mwisho itahusisha hali nyingi za utumaji kwa wakati mmoja au hali tofauti za uendeshaji kwa kisambazaji moduli cha kusimama pekee katika seva pangishi, mtengenezaji anapaswa kushauriana na mtengenezaji wa moduli kwa mbinu ya usakinishaji katika mfumo wa mwisho.

2.4 Taratibu za moduli chache
Haitumiki

2.5 Fuatilia miundo ya antena
Haitumiki

2.6 Mazingatio ya mfiduo wa RF
The device has been evaluated to meet the general RF exposure requirements. The device can be used in mobile or fixed exposure conditions with a minimum distance of 20 cm between the radiator & user’s body.

2.7 Antena
This radio transmitter has been approved by the Federal Communications Commission to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.

2.8 Lebo na maelezo ya kufuata
The final end product must be labeled in a visible area with the following “Contains FCC ID: 2AN3WM5STAMPC6LORA”.

2.9 Taarifa kuhusu aina za majaribio na mahitaji ya ziada ya majaribio
The host manufacturer that installs this module with limited modular approval should perform the test of radiated emission and spurious emission according to FCC part 15C:15.247 and 15.209 requirement, only if the test result complies with FCC part 15.247 and 15.209 requirements, then the host can be sold legally.

Maagizo ya ujumuishaji kwa watengenezaji wa bidhaa mwenyeji kulingana na KDB 996369 D03 Mwongozo wa OEM v01

2.10 Jaribio la ziada, Kanusho la Sehemu ya 15 la Sehemu Ndogo ya B
This transmitter module is tested as a subsystem, and its certification does not cover the FCC Part 15 Subpart B (unintentional radiator) rule requirement applicable to the final host. The final host will still need to be reassessed for compliance to this portion of the rule requirements if applicable.

2.11 Kumbuka Mazingatio ya EMI
We recommend using “best practice” RF design engineering, testing, and evaluation in case non-linear interactions generate additional non-compliant limits due to module placement to host components or properties. The host manufacturer is responsible for ensuring compliance with the applicable FCC rules for the transmitters operating individually and simultaneously. This includes compliance for the summation of all emissions from all outputs occupying the same or overlapping frequency ranges, as defined by the applicable rules.

2.12 Jinsi ya Kufanya Mabadiliko - Kumbuka Muhimu
Katika tukio ambalo hali hizi haziwezi kufikiwa (kwa mfanoample, certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid, and the FCC ID cannot be used on the final product. In these circumstances, OEM integrator contacts Grantees to make permissive changes, or the OEM integrator will be responsible for reevaluating the end product (including the transmitter) and obtaining a separate FCC authorization.

Maadamu masharti yote hapo juu yametimizwa, majaribio zaidi ya kisambaza data hayatahitajika. Hata hivyo, kiunganishi cha OEM bado kina jukumu la kujaribu bidhaa zao za mwisho kwa mahitaji yoyote ya ziada ya kufuata yanayohitajika na sehemu hii iliyosakinishwa.