Vitambulisho vya Kebo vya Jonard Tools CM-RJ45/8 RJ45 kwa Mwongozo wa Maelekezo wa CM-100

Utangulizi

This manual provides essential information for the proper use and maintenance of the Jonard Tools CM-RJ45/8 RJ45 Cable Identifiers. These identifiers are designed to work exclusively with the Jonard Tools CM-100 Cable Mapper Pro, facilitating efficient identification and mapping of RJ45 network cables.

Bidhaa Imeishaview

The CM-RJ45/8 kit includes eight (8) numbered RJ45 network cable identifiers. These identifiers are passive devices that, when connected to network cables, allow the CM-100 Cable Mapper Pro to distinguish between multiple cables connected to a patch panel or wall plate.

Sifa Muhimu:

Numbered Identification: Each identifier is clearly numbered from 1 to 8 for easy port mapping.
CM-100 Compatibility: Specifically designed to integrate with the Jonard Tools CM-100 Cable Mapper Pro.
Simultaneous Mapping: Enables mapping of up to 8 network cables concurrently.

Pack of 8 Jonard Tools RJ45 Cable Identifiers

Image: A set of eight numbered RJ45 cable identifiers, designed for use with the CM-100 Cable Mapper Pro.

Sanidi

Ensure CM-100 is Ready: Verify that your Jonard Tools CM-100 Cable Mapper Pro is powered on and functioning correctly. Refer to the CM-100 manual for its specific setup instructions.
Connect Identifiers: Plug each CM-RJ45/8 identifier into the RJ45 ports of the network cables you wish to map. For example, if you are mapping cables from a patch panel, connect one identifier to each cable's end at the patch panel.
Prepare Remote End: At the remote end of the cable run (e.g., wall plate), ensure the CM-100 Cable Mapper Pro is ready to receive the signal.

Jonard Tools RJ45 Cable Identifier plugged into a wall plate

Image: A numbered RJ45 cable identifier inserted into a network wall plate, demonstrating its application for port identification.

Maagizo ya Uendeshaji

Follow these steps to use the CM-RJ45/8 identifiers with your CM-100 Cable Mapper Pro:

Connect CM-100: Connect the main unit of the CM-100 Cable Mapper Pro to the network cable at the testing location (e.g., the switch end or the other end of the cable run).
Anza Mtihani: On the CM-100, select the appropriate test mode for RJ45 cable mapping. The CM-100 will send a signal through the cable.
Identify Cable: The CM-100's display will show the identifier number corresponding to the cable it is connected to. This allows you to quickly match the remote end of the cable to its numbered identifier.
Repeat for All Cables: Repeat the process for each cable connected to an identifier until all desired cables are mapped.

Hand holding Jonard Tools CM-100 Cable Mapper Pro connected to a network cable in a server rack

Image: A technician using the CM-100 Cable Mapper Pro to test a network cable connected within a server rack, demonstrating cable mapping in a live environment.

Jonard Tools CM-100 Cable Mapper Pro connected to a network cable with an identifier

Image: The CM-100 Cable Mapper Pro connected to a network cable, with an RJ45 identifier visible, illustrating the compatibility and function of the system.

Matengenezo

Kusafisha: Keep the identifiers clean and free from dust and debris. Use a soft, dry cloth for cleaning. Avoid abrasive cleaners or solvents.
Hifadhi: Store the identifiers in a cool, dry place, away from direct sunlight and extreme temperatures. Keep them in their original packaging or a protective case to prevent damage.
Ukaguzi: Periodically inspect the RJ45 connectors for any signs of wear, bent pins, or damage. Replace any damaged identifiers to ensure accurate testing.

Kutatua matatizo

Tatizo	Sababu inayowezekana	Suluhisho
CM-100 does not detect identifier.	Identifier not fully inserted. Damaged identifier. Cable fault (open, short). CM-100 not in correct test mode.	Ensure identifier is securely seated in the RJ45 port. Try a different identifier. Test the cable for faults using the CM-100's primary functions. Verify the CM-100 is set to the correct mapping or identification mode.
Incorrect identifier number displayed.	Multiple identifiers connected to the same cable. Identifier malfunction.	Ensure only one identifier is connected to each cable being tested. Try a different identifier to confirm if the issue is with the identifier itself.

Vipimo

Mfano: CM-RJ45/8
Utangamano: Jonard Tools CM-100 Cable Mapper Pro
Aina ya Kiunganishi: RJ45
Aina ya Kebo: Ethaneti
Number of Identifiers: 8 (numbered 1-8)
Dimensions (per identifier): Takriban inchi 1.5 x 0.75 x 1.5
Uzito (jumla ya seti): Takriban wakia 0.81
Rangi: Clear with blue accents

Udhamini na Msaada

For information regarding warranty coverage, technical support, or replacement parts for your Jonard Tools CM-RJ45/8 RJ45 Cable Identifiers, please refer to the documentation provided with your CM-100 Cable Mapper Pro or visit the official Jonard Tools website. Specific warranty details for this accessory are typically covered under the main CM-100 product warranty.

Rasmi Webtovuti: www.jonard.com

	Mwongozo wa Maelekezo ya Kipima TV cha Cable cha CTV-8K chenye Kazi Nyingi \| Jonard Tools Mwongozo kamili wa maelekezo kwa ajili ya Kipima TV cha Kebo cha Jonard Tools CTV-8K chenye Kazi Nyingi, kinachoelezea vipengele vyake, uendeshaji, vipimo, na taarifa za usalama kwa wasakinishaji na mafundi.
	Mwongozo wa Maelekezo ya Kipima TV cha Kebo cha Jonard Tools CTV-8K chenye Kazi Nyingi Mwongozo kamili wa maelekezo kwa ajili ya Kipima Runinga cha Kebo cha Jonard Tools CTV-8K chenye Kazi Nyingi, kinachoelezea vipengele, uendeshaji, na vipimo vyake vya upimaji wa kamera ya IP, utambuzi wa mtandao, na uchanganuzi wa kebo.
	Mwongozo wa Maelekezo ya Kipima TV cha Kebo cha Jonard Tools CTV-8K chenye Kazi Nyingi Comprehensive instruction manual for the Jonard Tools CTV-8K Multifunction Cable TV Tester. This guide details its features, operation, safety precautions, and specifications for testing IP, Analog, and HD Coaxial cameras, along with PoE, HDMI, and various network diagnostic functions.
	Mwongozo wa Maelekezo ya Mita ya Nguvu ya Optiki ya Jonard Tools FPM-55 Mwongozo kamili wa maelekezo kwa ajili ya Kipima Nguvu cha Jonard Tools FPM-55, kinachoelezea vipengele vyake, vipimo, uendeshaji, kazi muhimu, mwongozo wa utatuzi wa matatizo, na taarifa za udhamini.
	Karatasi ya Data ya Zana za Jonard Mid Span & Tools Tools - MS-526, MS-446, MS-426, MS-326, MS-316, MS-306, MS-6, MS-26, MS-336 Laha ya kina ya data ya Zana za Mid Span & Ring zilizo na hati miliki ya Jonard Tools, iliyoundwa kwa ufikiaji bora na salama kwa nyaya za fiber optic. Inajumuisha vipimo, maagizo ya matumizi, na sehemu mbadala za miundo MS-526, MS-446, MS-426, MS-326, MS-316, MS-306, MS-6, MS-26, MS-336, na MS-600.
	Jonard Tools Universal Stripping Tool - Cable Stripping Guide Comprehensive instructions for the Jonard Tools Universal Stripping Tool (UST Series), covering coax, networking, and flat cable stripping with detailed steps and operational guidance.

Jonard Tools CM-RJ45/8