ELEGOO Mercury Plus 3.0 Wash Tank Instruction Manual

1. Utangulizi

This manual provides instructions for the proper use and maintenance of the ELEGOO Mercury Plus 3.0 Wash Tank. This large-capacity washing container is designed for efficient post-processing of resin 3D printed models, offering compatibility with the Mercury Plus V3.0 Wash and Cure Station.

The wash tank features a generous 7.5L capacity, allowing for the cleaning of larger models or multiple smaller prints simultaneously. Its design incorporates features for both basket and hanging cleaning methods, ensuring thorough resin removal.

Mbele view of the ELEGOO Mercury Plus 3.0 Wash Tank, showing its clear plastic construction and 7.5L maximum fill line.

Kielelezo 1: Mbele view of the ELEGOO Mercury Plus 3.0 Wash Tank, displaying its clear plastic construction and the 7.5L maximum fill line.

2. Yaliyomo kwenye Kifurushi

Thibitisha kuwa vipengele vyote vipo kwenye kifurushi:

ELEGOO Mercury Plus 3.0 Wash Tank (7.5L capacity)
Kuosha Kikapu
Adjustable Build Plate Holders (2 pieces)
Hex Key and Screws (for assembly of build plate holders)

Contents of the ELEGOO Mercury Plus 3.0 Wash Tank package, including the tank, washing basket, and small accessories.

Figure 2: Package contents, showing the wash tank, washing basket, and additional accessories.

3. Kuweka

Fungua Vipengee: Ondoa kwa uangalifu vitu vyote kutoka kwa kifurushi.
Chunguza Uharibifu: Check the wash tank and accessories for any signs of damage during transit. Contact support if any issues are found.
Andaa Suluhisho la Kusafisha: Fill the wash tank with an appropriate cleaning solution (e.g., Isopropyl Alcohol, Ethanol) up to the MAX 7.5L line, or to a level sufficient to submerge your printed models.
Install Build Plate Holders (if using hanging mode): If you intend to clean models directly on the build plate, attach the adjustable build plate holders to the washing basket using the provided hex key and screws. Ensure they are securely fastened and adjusted to fit your specific build plate size.

Karibu-up view of the magnetic stirring plate at the bottom of the wash tank, designed to agitate the cleaning solution.

Figure 3: Detail of the magnetic stirring plate within the wash tank, which facilitates efficient cleaning solution agitation.

4. Maagizo ya Uendeshaji

The ELEGOO Mercury Plus 3.0 Wash Tank supports two primary cleaning modes:

4.1 Basket Cleaning Mode

This mode is suitable for models that have been removed from the build plate.

Carefully remove your 3D printed model(s) from the build plate.
Place the model(s) into the washing basket.
Lower the washing basket into the wash tank, ensuring the models are fully submerged in the cleaning solution.
Close the lid securely to prevent splashes and evaporation.
Initiate the washing cycle on your Mercury Plus V3.0 Wash and Cure Station (sold separately).
After the cleaning cycle, remove the basket, allow excess solution to drip off, and proceed with drying and curing the models.

Maximum washing volume for basket cleaning: 230 × 135 × 260 mm.

4.2 Hanging Cleaning Mode

This mode allows for cleaning models directly on the build plate, minimizing handling.

Attach the adjustable build plate holders to the washing basket (if not already done).
Secure your build plate, with the printed model(s) still attached, onto the adjustable holders within the washing basket.
Lower the washing basket and build plate assembly into the wash tank, ensuring the models are fully submerged in the cleaning solution.
Funga kifuniko kwa usalama.
Initiate the washing cycle on your Mercury Plus V3.0 Wash and Cure Station.
After the cleaning cycle, carefully remove the build plate, allow excess solution to drip off, and proceed with model removal, drying, and curing.

Maximum washing volume for hanging cleaning: 214 × 135 × 180 mm.

Mwenye pembe view of the ELEGOO Mercury Plus 3.0 Wash Tank, showing its rectangular shape and clear construction.

Kielelezo 4: Pembe view of the wash tank, highlighting its overall design and capacity markings.

5. Matengenezo

Kusafisha tanki: Regularly clean the wash tank and basket with warm water and mild soap. Ensure all resin residue is removed.
Ubadilishaji wa Suluhisho: Replace the cleaning solution periodically, especially when it becomes cloudy or heavily saturated with resin. Dispose of used resin-contaminated solution according to local regulations.
Muhuri wa Kifuniko: Ensure the rubber seal on the lid is clean and free of debris to maintain a tight, splash-proof, and evaporation-resistant closure.
Hifadhi: Store the wash tank in a cool, dry place away from direct sunlight when not in use. The tank is made of high-quality PP plastic, offering chemical and heat resistance for durability.

6. Utatuzi wa shida

Resin Residue After Washing:
- Ensure models are fully submerged in the cleaning solution.
- Check the cleaning solution concentration and replace if it appears diluted or heavily contaminated.
- Increase washing time or consider a second wash cycle.
Kifuniko hakijafungwa vizuri:
- Inspect the rubber seal for any damage or debris. Clean or replace if necessary.
- Ensure the lid is correctly aligned and latched on all sides.

7. Vipimo

Jina la Bidhaa	ELEGOO Mercury Plus 3.0 Wash Tank
Nambari ya Mfano	UK-EHJ-3DL-QXT3
Chapa	ELEGOO
Washing Volume (with platform cleaning)	214 × 135 × 180 mm
Washing Volume (without platform cleaning)	230 × 135 × 260 mm
Jumla ya Uwezo	7.5 lita
Nyenzo	High-quality PP Plastic
Vipimo vya Kifurushi	34 x 26 x 8 cm
Uzito wa Kifurushi	1.35 kg

8. Udhamini na Msaada

For warranty information or technical support, please refer to the official ELEGOO website or contact ELEGOO customer service directly. Keep your purchase receipt as proof of purchase.

Official ELEGOO Webtovuti: www.elegoo.com

	Mashine ya Kuosha na Kufua ya ELEGOO Mercury Plus: Mwongozo wa Mtumiaji na Uendeshaji Mwongozo kamili wa mtumiaji wa Mashine ya Kuosha na Kufua ya ELEGOO Mercury Plus, inayoelezea vipengele vyake, njia za uendeshaji (kuosha na kupoza), na mbinu bora za modeli zilizochapishwa za 3D baada ya usindikaji.
	Mwongozo wa Uendeshaji wa Kifurushi cha ELEGOO Mercury XS: Osha, Tibu, na UV Lamp Mwongozo wa kina wa utendakazi wa Kifurushi cha ELEGOO Mercury XS, usanidi wa kina, vigezo vya msingi, yaliyomo kwenye kifurushi, maagizo ya kufanya kazi kwa vitengo vya Mercury X Wash na Mercury XS Cure, UV l ya mkononi.amp matumizi, matengenezo, na utatuzi wa matatizo. Muhimu kwa uchapishaji wa 3D baada ya kuchakata.
	ELEGOO MERCURY PLUS Wash & Cure Machine Operation Manual Official operation manual for the ELEGOO MERCURY PLUS Wash & Cure Machine, detailing setup, operation modes (wash and cure), maintenance, and troubleshooting for 3D print post-processing.
	ELEGOO MERCURY PLUS 2.0 Osha & Tibu Mwongozo wa Mtumiaji wa Mashine Mwongozo rasmi wa uendeshaji wa Mashine ya Kuosha na Kuponya ya ELEGOO MERCURY PLUS 2.0. Hutoa maelezo ya kina juu ya specifikationer kiufundi, bidhaa juuview, hali ya safisha, hali ya tiba, taratibu za matengenezo, na Maswali Yanayoulizwa Mara kwa Mara ya utatuzi.
	Mwongozo wa Mipangilio ya Kichapishi cha 3D cha ELEGOO Saturn 4 Ultra 16K Mwongozo wa kina wa mipangilio ya uchapishaji ya resini mbalimbali kwenye kichapishi cha ELEGOO Saturn 4 Ultra 16K 3D, ikijumuisha nyakati za kukaribia zilizopendekezwa, urefu wa safu na vigezo vingine kwa matokeo bora.
	Mwongozo wa Mipangilio ya Resin ya Printa ya 3D ya ELEGOO Mars 4 Mwongozo wa kina wa mipangilio ya resini kwa kichapishi cha ELEGOO Mars 4 Ultra 3D, kinachojumuisha aina mbalimbali za resini na vigezo vyake vya uchapishaji vyema.

ELEGOO UK-EHJ-3DL-QXT3