1. Utangulizi
This manual provides detailed instructions for the proper installation, operation, and maintenance of the GODIYMODULES High Voltage DC Converter Module Board. This module is designed to provide stable high voltage DC and filament voltage, suitable for applications such as powering Nixie tubes and Magic Eye tubes.
Picha 1.1: Juu-chini view of the GODIYMODULES High Voltage DC Converter Module Board. This image shows the overall layout of the components, including capacitors, inductors, the DC input jack, and the terminal blocks for input and output connections.
2. Taarifa za Usalama
WARNING: This module generates high voltage. Improper handling can result in electric shock, injury, or damage to equipment. Always exercise extreme caution when working with high voltage mizunguko.
- Ensure the power supply is disconnected before making any connections or adjustments.
- Do not touch any components on the board when power is applied.
- Use appropriate insulation and safety equipment.
- Verify all connections are correct before applying power.
- This module is intended for experienced electronics hobbyists and professionals.
3. Vipengele
- Designed for Nixie and Magic Eye Tube anode and filament power supply.
- Kiwango cha juu kinachoweza kurekebishwatage DC output.
- Dedicated 6.3V filament voltagpato.
- Compact board design.
4. Vipimo
| Kigezo | Thamani |
|---|---|
| Uingizaji Voltage | DC 9V-12V |
| DC Socket Specification | 5.5*2.1 mm (Inner Positive, Outer Negative) |
| Kiwango cha juutage Pato | DC 150V-280V / 15mA (Adjustable) |
| Filament Voltage Pato | DC 6.3V / 1500mA |
| Vipimo | Takriban inchi 5.24 x 3.82 x 1.34 (Kifurushi) |
| Uzito | Takriban wakia 0.634 |
| Nyenzo | Metali, Plastiki |
5. Mipangilio na Viunganisho
Follow these steps to correctly connect the High Voltage DC Converter Module Board to your system. Ensure all power is disconnected before proceeding.
5.1 Muunganisho wa Nguvu ya Kuingiza
The module accepts a DC input voltage between 9V and 12V. There are two methods for providing input power:
- DC Power Jack: Use a DC power adapter with a 5.5*2.1 mm plug. The plug must be inner positive and outer negative.
- Kizuizi cha Kituo: Connect your DC 9V-12V power supply to the designated input terminals on the green screw terminal block. Observe correct polarity.
Image 5.1: Connection diagram showing input and output terminals. The DC 9-12V input can be connected via the barrel jack (5.5*2.1mm, inner positive, outer negative) or the screw terminal block. The image also indicates the output voltage regulation potentiometer.
Image 5.2: Detailed connection diagram illustrating the input power options (DC 9-12V via barrel jack or screw terminals) and the output connections for 6.3V filament voltage, GND, and adjustable DC 150-280V. The output voltage adjustment potentiometer is also clearly marked.
5.2 Miunganisho ya Pato
The module provides two main outputs via the green screw terminal block:
- DC 150V-280V Output: Hii ni sauti ya juutage output, adjustable via the onboard potentiometer. Connect the anode of your Nixie or Magic Eye tube to this output.
- Pato la DC 6.3V: This output provides 6.3V for tube filaments. Connect the filament of your tube to this output.
- GND: Common ground connection for both outputs.
Ensure all connections are secure and correctly polarized before applying power.
6. Maagizo ya Uendeshaji
6.1 Kuwasha
Once all connections are verified and secure, connect the DC 9V-12V power supply to the module. The module will immediately begin generating the output voltages.
6.2 Adjusting High Voltage Pato
Voltage output (DC 150V-280V) is adjustable using the blue potentiometer located on the board. Use a small screwdriver to carefully turn the potentiometer:
- Kugeuka mwendo wa saa mapenzi kuongezeka juzuu ya patotage.
- Kugeuka mwendo wa saa mapenzi kupungua juzuu ya patotage.
Always use a multimeter to measure the output voltage while adjusting to prevent over-voltage damage to your connected components.
Picha 6.1: Juu view of the module, clearly showing the blue potentiometer used for adjusting the high voltagpato.
7. Matengenezo
The GODIYMODULES High Voltage DC Converter Module Board is designed for reliable operation and requires minimal maintenance.
- Weka moduli safi na isiyo na vumbi na uchafu.
- Ensure adequate ventilation around the module to prevent overheating.
- Epuka kuweka moduli kwa unyevu au joto kali.
- Regularly inspect connections for looseness or corrosion.
8. Utatuzi wa shida
- Hakuna Towe Voltage:
- Verify the input power supply is connected and providing 9V-12V DC.
- Check the polarity of the input DC power plug (inner positive, outer negative).
- Ensure all output connections are secure.
- Toleo Lisilo Sahihi la Matokeotage:
- Kwa sauti ya juutage output, adjust the potentiometer as described in Section 6.2.
- Use a multimeter to accurately measure the output voltages.
- Hakikisha ujazo wa uingizajitage ni thabiti na ndani ya safu maalum.
- Kuongeza joto kwa moduli:
- Ensure adequate airflow around the module.
- Verify that the load connected to the outputs does not exceed the specified current limits (15mA for HV, 1500mA for 6.3V).
9. Msaada
For further assistance or technical inquiries, please refer to the seller's contact information on the product purchase page or visit the GODIYMODULES official support channels.
