Mwongozo wa Mtumiaji wa Kidhibiti cha Kifungua Mlango wa Gereji cha Genie 39165R

Utangulizi

This manual provides detailed instructions for the installation, operation, and maintenance of your Genie Garage Door Opener Controller, model 39165R. This controller is compatible with Genie garage door openers that use models 34026A-R1, Series II, and 37351R. Please read this manual thoroughly before use to ensure proper function and safety.

Genie Garage Door Opener Controller 39165R

A gray Genie garage door opener controller with a white faceplate, featuring a large primary button, lock/unlock icons, and a light bulb icon. The Genie logo is prominently displayed in red.

Maagizo Muhimu ya Usalama

Always keep the remote controls out of reach of children.
Do not allow children to operate the garage door opener.
Ensure the garage door is visible and clear of obstructions before operating.
Regularly inspect the garage door system for proper balance and operation.

Kuweka na Kuweka

Programming Your Controller

This section outlines the steps to program your new Genie Garage Door Opener Controller 39165R to your existing Genie garage door opener.

Step 1: Locate the Learn Button

The "Learn" button is typically found on the motor head of your garage door opener. Its color may vary (e.g., red, purple, orange, green). Refer to your specific garage door opener's manual if you cannot locate it.

Step 2: Initiate Programming

Press and immediately release the "Learn" button on your garage door opener motor head. The LED indicator light next to the button will illuminate.
Within 30 seconds, press and hold the desired button on your new 39165R controller for approximately 2 seconds.
Release the button. The garage door opener's light will flash once, or you may hear a click, indicating successful programming.

Step 3: Test the Controller

Press the programmed button on your 39165R controller. The garage door should activate. If it does not, repeat the programming steps.

Maagizo ya Uendeshaji

Your 39165R controller features buttons for opening/closing the garage door and controlling the opener's light.

Garage Door Operation: Press the large primary button to open or close the garage door. Pressing it again during operation will stop the door.
Udhibiti wa Mwanga: Press the button with the light bulb icon to turn the garage door opener's light on or off, independent of door movement.
Lock Feature (if applicable): Some models may have a lock button (represented by padlock icons). Consult your opener's manual for specific functionality.

Matengenezo

Ubadilishaji wa Betri

The 39165R controller uses a standard coin cell battery (e.g., CR2032). When the range decreases or the LED indicator on the controller fails to light up, it's time to replace the battery.

Locate the small screw or tab on the back or side of the controller casing.
Use a small screwdriver or coin to open the casing.
Carefully remove the old battery. Note its orientation (+/-).
Ingiza betri mpya yenye polarity sahihi.
Funga casing salama.

Kusafisha

Wipe the controller with a soft, dry cloth. Avoid using harsh chemicals or abrasive cleaners.

Kutatua matatizo

Masuala ya Kawaida na Suluhisho

Kidhibiti Haifanyi kazi:
- Angalia Betri: Replace the battery if it's low or dead.
- Reprogram: The controller may have lost its programming. Follow the "Setup and Installation" steps to reprogram it.
- Masuala mbalimbali: Ensure there are no obstructions between the controller and the garage door opener. Check for interference from other electronic devices.
Garage Door Not Responding:
- Ugavi wa Nguvu: Verify the garage door opener has power.
- Sensorer za Usalama: Check if the safety sensors are aligned and free of obstructions.
- Manual Disconnect: Ensure the emergency release cord has not been pulled, disconnecting the door from the opener.

If problems persist after attempting these solutions, consult a qualified garage door technician.

Vipimo

Vipimo vya Bidhaa

Mfano: 39165R
Utangamano: Genie garage door openers compatible with models 34026A-R1, Series II, 37351R.
Chanzo cha Nguvu: Battery (e.g., CR2032, not included)
Vipimo: Takriban inchi 5 x 3 x 1.4 (Vipimo vya Kifurushi)
Uzito: Takriban wakia 7.2 (Uzito wa Bidhaa)
Mtengenezaji: Generic (functions as a Genie compatible part)

	Mwongozo wa Programu ya Kufungua Mlango wa Gereji ya Genie: Mifumo ya Makazi na Biashara Mwongozo kamili wa kupanga vifungua milango ya gereji vya makazi na biashara vya Genie, ikiwa ni pamoja na mifumo kuanzia 1995 hadi uzalishaji wa sasa. Jifunze jinsi ya kupanga vidhibiti vya mbali, kubadilisha betri, na kutatua matatizo ya kawaida. Hushughulikia aina mbalimbali za pedi za vitufe vya programu na maonyo ya usalama.
	Maelekezo ya Uendeshaji wa Kinanda cha Kisichotumia Waya cha Genie Mwongozo kamili wa vitufe visivyotumia waya vya Genie Intellicode, unaohusu programu, uendeshaji, uwekaji, ubadilishaji wa betri, na utatuzi wa matatizo. Unajumuisha maonyo ya usalama na taarifa za udhibiti.
	Genie 7155-TKV Smart Garage Door Opener Installation Manual Comprehensive installation manual for the Genie 7155-TKV StealthDrive Connect Smart Garage Door Opener, covering pre-installation, assembly, mounting, wiring, and safety instructions.
	Maelekezo ya Kinanda cha Genie GK-R Kisichotumia Waya Hati hii inatoa maagizo ya kupanga na kuendesha Kibodi Isiyotumia Waya ya Genie GK-R kwa vifungua milango ya gereji. Inashughulikia usanidi wa PIN, kupanga kwa milango moja na mingi, uendeshaji wa kibodi, kupachika, kubadilisha betri, na kuweka upya kibodi kwenye chaguo-msingi za kiwandani.
	Mwongozo wa Ubadilishaji wa Mlango wa Genie Garage kopo Maagizo ya hatua kwa hatua ya kubadilisha injini kwenye kopo la mlango wa karakana ya Genie, ikijumuisha tahadhari za usalama na maelezo ya kina ya mchoro.
	Mwongozo wa Kubadilisha Pulley ya Genie Idler Maagizo ya hatua kwa hatua ya kubadilisha pulley ya idler kwenye kifungua mlango wa gereji cha Genie. Inajumuisha maonyo, zana zinazohitajika, na taratibu za kina za ukarabati salama na ufanisi.

Genie 39165R