Mwongozo wa Mtumiaji wa Kituo cha Urekebishaji wa Hewa ya Joto cha JBC JTSE-2QA

Utangulizi

This user manual provides comprehensive instructions for the safe and efficient operation, setup, and maintenance of the JBC JTSE-2QA Digital Hot Air Rework Station. Please read this manual thoroughly before using the device to ensure optimal performance and longevity.

Bidhaa Imeishaview

JBC JTSE-2QA Digital Hot Air Rework Station with hot air tool and stand

Figure 1: The JBC JTSE-2QA Digital Hot Air Rework Station, featuring the main unit with digital display, the hot air tool, and its dedicated stand. This station is designed for precise and controlled hot air applications in electronics rework.

The JBC JTSE-2QA is a high-performance digital hot air rework station designed for professional electronics repair and assembly. It offers precise temperature control and airflow management, making it ideal for desoldering and soldering surface-mount components (SMD).

Maagizo ya Usalama

Daima zingatia tahadhari zifuatazo za usalama ili kuzuia majeraha na uharibifu wa kifaa:

Ensure the station is connected to a properly grounded power outlet (230V).
Do not touch the hot air nozzle or heated components directly. Use appropriate tools and allow components to cool.
Operate the station in a well-ventilated area to dissipate fumes.
Keep flammable materials away from the hot air stream.
Disconnect the power cord before performing any maintenance or cleaning.
Do not operate the station if the power cord or unit is damaged.
This device is for professional use only. Keep out of reach of children.

Sanidi

Kufungua: Ondoa kwa uangalifu vifaa vyote kutoka kwa kifurushi. Thibitisha kuwa vipengee vyote vilivyoorodheshwa katika sehemu ya "Nini kwenye Kisanduku" vipo.
Uwekaji: Place the main unit on a stable, heat-resistant, and level surface. Ensure adequate clearance around the unit for ventilation.
Connect Hot Air Tool: Connect the hot air tool's hose and electrical connector to the corresponding ports on the main unit. Ensure a secure connection.
Connect Stand: Position the hot air tool stand near the main unit and place the hot air tool securely in its holder when not in use. The stand often includes a sensor to detect when the tool is placed, activating standby mode.
Muunganisho wa Nishati: Plug the power cord into the main unit's power inlet, then connect it to a grounded 230V AC power outlet.

Maagizo ya Uendeshaji

1. Kuwasha/Kuzima

Press the power button located on the front panel to turn the station on or off. The digital display will illuminate upon startup.

2. Setting Temperature and Airflow

Tumia vitufe vya kusogeza (+, -, OK) on the front panel to adjust the hot air temperature and airflow settings. The display shows the current and set values. The temperature range is typically 150°C to 450°C.

Halijoto: Adjust the desired hot air temperature for your application.
Mtiririko wa hewa: Control the air volume output from the nozzle. Start with lower airflow for delicate components and increase as needed.

3. Using the Hot Air Tool

When the hot air tool is removed from its stand, the heating element will activate and the station will begin to reach the set temperature. When returned to the stand, the station will enter standby mode, cooling down the tool to a safe temperature.

Chagua pua inayofaa kwa programu yako.
Maintain a safe distance between the nozzle and the component to avoid overheating.
Move the hot air tool in a circular motion to ensure even heating.

Matengenezo

Regular maintenance ensures the longevity and optimal performance of your JBC JTSE-2QA station.

Kusafisha: Kata umeme kabla ya kusafisha. Tumia kifaa laini, damp cloth to wipe down the exterior of the main unit and the hot air tool. Do not use abrasive cleaners or solvents.
Utunzaji wa Nozzle: Periodically inspect the hot air nozzles for blockages or damage. Clean them as needed to ensure proper airflow.
Kichujio cha Hewa: Check and clean or replace the air filter (if applicable) according to the manufacturer's recommendations to maintain optimal airflow and prevent dust accumulation.
Hifadhi: Store the station in a clean, dry environment when not in use.

Kutatua matatizo

Tatizo	Sababu inayowezekana	Suluhisho
Station does not power on.	No power supply; loose power cord.	Angalia uunganisho wa nguvu; hakikisha duka linafanya kazi.
Hot air tool not heating.	Tool not properly connected; tool in stand (standby mode); faulty heating element.	Ensure tool is securely connected and removed from stand; contact support if element is faulty.
Upepo wa kutosha wa hewa.	Blocked nozzle; dirty air filter.	Clean or replace nozzle; check and clean/replace air filter.
Temperature fluctuations.	Sensor issue; unstable power supply.	Ensure stable power; contact support for sensor issues.

Vipimo

Kipengele	Maelezo
Nambari ya Mfano	JTSE-2QA
Mtengenezaji	JBC
Uingizaji Voltage	230 Volts AC
Kiwango cha Joto	150 - 450 °C (302 - 842 °F)
Vipimo (L x W x H)	474 x 368 x 195 cm
Uzito wa Kipengee	Kilo 4.1 (Gramu 4104)
Vipengee vilivyojumuishwa	Kituo cha Urekebishaji hewa cha Moto
Idadi ya Vituo	1

Udhamini na Msaada

For warranty information, technical support, or service inquiries regarding your JBC JTSE-2QA Digital Hot Air Rework Station, please contact JBC customer service or visit their official webtovuti. Weka risiti yako ya ununuzi kama dhibitisho la ununuzi kwa madai ya udhamini.

JBC Official Webtovuti: www.jbctools.com

	Mwongozo wa Maelekezo ya Kitengo cha Udhibiti wa Hewa ya Moto wa JBC JTSE Mwongozo kamili wa maelekezo kwa Kitengo cha Udhibiti wa Hewa Moto cha JBC JTSE Power, unaelezea vipengele, uendeshaji, matengenezo, na vipimo. Jifunze jinsi ya kutumia na kutunza vifaa vyako vya kusubu vya JBC.
	JBC MV Pneumatic Desoldering Moduli kwa DI Mwongozo wa Maagizo Mwongozo wa maagizo wa Moduli ya Utengano wa Nyuma ya JBC MV kwa DI, inayoeleza kwa kina vipengele vyake, miunganisho, matengenezo, tahadhari za usalama, vipimo, na maelezo ya udhamini. Mwongozo muhimu kwa uendeshaji sahihi na utunzaji.
	Mwongozo wa Mtumiaji wa JBC P405 Foot Pedal Mwongozo wa mtumiaji wa kanyagio cha mguu wa JBC P405, ukielezea sifa zake, miunganisho, uoanifu, usanidi wa vituo na moduli mbalimbali za JBC, na matumizi ya zamani.amples kwa desoldering na soldering.
	JBC DDSE 2-Tool Rework Station - Product Overview na Mwongozo wa Ufungaji Explore the JBC DDSE 2-Tool Rework Station with this Plug & Play Guide. Learn about its components, packing list, installation process, technical specifications including model numbers DDSE-9QE, DDSE-1QE, DDSE-2QE, and warranty information. Features ESD safe and CE compliance.
	JBC DIS-D Premium Desoldering Station with Electric Pump - User Manual & Specifications Detailed information on the JBC DIS-D Premium Desoldering Station with Electric Pump, including packing list, features, compatibility, maintenance, safety guidelines, specifications, and warranty.
	JBC P405 Pedal Instruction Manual - Solder Station Accessory Comprehensive instruction manual for the JBC P405 Pedal, detailing its setup, compatibility, configuration, and use in electronic rework processes with JBC soldering stations and tools.

JBC JTSE-2QA