Mwongozo wa Mtumiaji wa INTI2/A wa Nice Apollo Inti Mini Transmitter yenye Vituo Viwili

Utangulizi

This manual provides essential instructions for the proper setup, operation, and maintenance of your Nice Apollo Inti 2-Channel Mini Transmitter, model INTI2/A. This miniature remote control is designed for use with USA Nice/Apollo 433 MHz receivers, offering a secure and efficient solution for gate automation.

The Inti transmitter features advanced data processing and recognition systems, enhancing security and reducing automation response times for faster gate opening and closing. It operates on a 433.92 MHz rolling code frequency with 72-bit O-Code encoding, ensuring compatibility with Nice FLOR encoding receivers.

Important Compatibility Note: This transmitter is designed exclusively for USA Nice/Apollo receivers (models ending with "/A"). It is not compatible with Nice European models, even if they appear similar.

Taarifa za Usalama

• Ushughulikiaji wa Betri: Keep batteries out of reach of children. Do not short-circuit batteries. Install batteries correctly, ensuring the positive side is oriented as indicated.
• Usakinishaji: Always follow the provided instructions carefully to prevent damage to the device or potential injury.
• Uendeshaji bila waya: This device operates on a wireless frequency and may cause interference with other wireless devices. Avoid placing it near sensitive electronic equipment.

Bidhaa Imeishaview

Setup: Programming the Transmitter

The Nice Apollo Inti transmitter can be programmed using an existing programmed transmitter or directly to the receiver board. Ensure your receiver is a USA Nice/Apollo 433 MHz model (e.g., Nice Model 1050).

Method 1: Programming from an Existing Transmitter (Code Exchange)

This method allows you to easily program a new transmitter using one that is already linked to your receiver.

1. Take an already programmed Nice Apollo Inti transmitter.
2. Bonyeza na ushikilie kitufe kwenye zilizopo transmitter that you wish to copy. The LED on the existing transmitter will illuminate.
3. While still holding the button on the existing transmitter, press and hold the corresponding button on the mpya kisambazaji.
4. Continue holding both buttons until the LED on the new transmitter flashes three times, then remains solid. This indicates successful programming.
5. Release both buttons. Test the new transmitter with your gate opener.

Method 2: Programming Directly to the Nice Apollo 1050 Receiver Board

This method is used when an existing programmed transmitter is not available or if you are setting up the system for the first time. This process involves interacting directly with the receiver unit.

1. Locate the programming button on your Nice Apollo 1050 receiver board. This is typically a small button near the receiver module.
2. Press the programming button on the receiver board mara moja. An LED on the receiver will start to flash slowly.
3. Wait for the LED on the receiver to flash for a few seconds, then press and hold the programming button again until the LED turns kijani kibichi. This indicates the receiver is ready to learn a new code.
4. Immediately press and hold the desired button on your Nice Apollo Inti transmitter (e.g., the bottom button).
5. Observe the LED on the receiver. It should flash three times, then return to a solid green state. This confirms successful programming of that button.
6. Release the button on the transmitter. You have approximately 10 seconds to program another button or another remote before the receiver exits programming mode.
7. Repeat steps 4-6 for any additional buttons or transmitters you wish to program.
8. After programming all desired transmitters, wait for the receiver's LED to turn off (or return to its normal operating state) to exit programming mode.
9. Test the newly programmed transmitter with your gate opener.

Uendeshaji wa Transmitter

The Nice Apollo Inti 2-Channel Mini Transmitter is designed for straightforward operation of your gate opener.

1. Ensure you are within the operational range of your gate opener (up to 150 meters or 500 feet outdoors).
2. Press the programmed button on your transmitter once to activate the gate.
3. Depending on your gate system's configuration, a single press typically initiates the opening or closing sequence. Pressing the button again during operation may stop the gate.

Matengenezo

Ubadilishaji wa Betri

The Nice Apollo Inti transmitter uses a Lithium battery. While battery life is typically several years, replacement will eventually be necessary.

Ili kubadilisha betri:

1. Carefully pry open the casing of the transmitter. This may require a small, flat tool.
2. Ondoa betri ya zamani.
3. Insert a new Lithium battery, ensuring correct polarity (positive side first).
4. Piga picha ya casing kurudi pamoja salama.

Note: Some Nice remote models may be more challenging to open for battery replacement, requiring careful prying. The Era One model, for example, has a more accessible battery compartment compared to the smaller Inti models.

Kutatua matatizo

• Transmitter not responding:
  • Angalia betri. Badilisha ikiwa ni lazima.
  • Ensure you are within the operational range of the receiver.
  • Verify that the transmitter is correctly programmed to your receiver. Refer to the "Setup" section.
• Ugumu wa programu:
  • Confirm your receiver is a USA Nice/Apollo 433 MHz model (e.g., "/A" model). European models are not compatible.
  • Ensure the receiver is in the correct learning mode (solid green LED on the 1050 board).
  • When programming to the board, ensure you press the receiver's programming button once, wait for slow flashing, then press and hold until solid before pressing the remote button.
  • If programming from an existing remote, ensure both remotes are held close together and buttons are pressed simultaneously as instructed.
• Kuingilia:
  • If the gate operates erratically or not at all, check for other wireless devices operating nearby that might cause interference.
  • Ensure the receiver antenna is unobstructed and properly positioned.

Vipimo

Udhamini na Msaada

For warranty information, technical support, or further assistance, please contact your authorized Nice Apollo dealer or the manufacturer directly. Ensure you have your product model number (INTI2/A) and purchase details available when seeking support.