Utangulizi
The JBL Studio 550P is a 10-inch powered subwoofer designed to enhance your audio experience by delivering powerful and detailed low-frequency sound. This manual provides essential information for the proper setup, operation, and maintenance of your subwoofer, ensuring optimal performance and longevity.
Upande wa mbele view of the JBL Studio 550P 10-Inch Powered Subwoofer, showcasing its black finish and sleek design.
Sifa Muhimu
- 10-Inch PolyPlas Woofer: Features an ultra-ridged PolyPlas cone and cast frame for deep bass impact and excitement without distortion.
- Powerful 300W RMS Ampmaisha: Imejengwa ndani amplifier delivers 300 watts RMS (500 watts peak) for robust and clear low-frequency reproduction.
- Uzio Uliofungwa: Provides tight, accurate bass response.
- Forward-Firing Transducer: Maximizes bass impact and performance.
- Ingizo Mbalimbali: Equipped with LFE and Line-level (RCA) inputs for flexible connectivity with various receivers and processors.
- Adjustable Crossover Frequency: Allows optimization of subwoofer performance to seamlessly integrate with main speakers.
- Udhibiti wa Awamu: Increases installation flexibility and helps achieve optimal sound alignment.
- Metal Floor Spikes: Improves bass impact and reduces unwanted resonance.
- Auto Turn-On and Turn-Off: For convenient use and energy conservation.
Sanidi
Proper placement and connection are crucial for achieving the best sound quality from your JBL Studio 550P subwoofer. Follow these steps for initial setup:
- Uwekaji: Position the subwoofer in your listening area. Experiment with different locations to find the spot that provides the most balanced and impactful bass. Corner placement often enhances bass output.
- Muunganisho wa Nishati: Connect the supplied power cord to the subwoofer's power input and then to a suitable electrical outlet (120V, 60Hz for US models; 220V-230V, 50Hz/60Hz for EU models).
- Uunganisho wa Sauti:
- LFE Input (Recommended for Home Theater): Connect an RCA cable from your receiver's LFE or Subwoofer Output to the LFE Input on the subwoofer.
- Line-Level Inputs (Stereo Receivers/Preamps): Connect RCA cables from your receiver's stereo pre-out (Left and Right) to the Line-Level Inputs (Left and Right) on the subwoofer.
- Kuwasha kwa Awali: Turn on the subwoofer using the power switch. The auto turn-on feature will activate the subwoofer when an audio signal is detected.
- Speaker Integration: If your receiver has a built-in crossover, set the subwoofer's crossover frequency control to its highest setting (LFE mode). If your receiver does not have a subwoofer crossover, adjust the subwoofer's crossover control to blend seamlessly with your main speakers (typically between 80Hz and 100Hz).
- Marekebisho ya Awamu: Use the phase control (0° or 180°) to ensure the subwoofer's output is in phase with your main speakers. Listen for the most impactful and coherent bass.
- Marekebisho ya Sauti: Start with the subwoofer's volume control at a low setting and gradually increase it until the bass output blends well with your main speakers without overpowering them.
Maagizo ya Uendeshaji
Once set up, operating your JBL Studio 550P is straightforward:
- Washa/Zima: The subwoofer features an auto turn-on/off function. It will automatically power on when an audio signal is detected and enter standby mode after a period of inactivity. You can also manually turn it on or off using the power switch on the rear panel.
- Udhibiti wa Sauti: Adjust the volume knob on the rear panel to control the subwoofer's output level. Fine-tune this to achieve a balanced sound with your main speakers.
- Mzunguko wa Kuvuka: The crossover frequency knob allows you to set the upper frequency limit for the subwoofer. Frequencies above this setting will be sent to your main speakers. Adjust this to ensure a smooth transition between the subwoofer and your main speakers.
- Kubadilisha Awamu: The phase switch (0°/180°) helps align the subwoofer's sound waves with those of your main speakers. If the bass sounds weak or hollow, try flipping the phase switch.
Matengenezo
To maintain the performance and appearance of your JBL Studio 550P subwoofer, follow these simple maintenance guidelines:
- Kusafisha: Use a soft, dry cloth to clean the cabinet. Avoid using abrasive cleaners, waxes, or solvents, as these can damage the finish.
- Utunzaji wa Grille: The speaker grille can be gently removed for cleaning. Use a soft brush or vacuum cleaner with a brush attachment to remove dust.
- Uwekaji: Ensure the subwoofer is placed on a stable, level surface. Avoid placing it in direct sunlight, near heat sources, or in areas with excessive moisture.
- Uingizaji hewa: Ensure adequate ventilation around the subwoofer to prevent overheating. Do not block any vents.
Kutatua matatizo
If you experience issues with your JBL Studio 550P subwoofer, consult the following troubleshooting guide:
- Hakuna Nguvu:
- Check if the power cord is securely connected to both the subwoofer and the electrical outlet.
- Thibitisha kuwa mkondo wa umeme unafanya kazi.
- Ensure the power switch on the subwoofer's rear panel is in the 'ON' position.
- Hakuna Sauti:
- Confirm that the audio input cables (RCA or LFE) are securely connected to both the subwoofer and your audio source (receiver/preamp).
- Check the volume level on the subwoofer and your audio source.
- Ensure the subwoofer is powered on (check the power indicator light).
- If using LFE input, ensure your receiver's subwoofer output is enabled and configured correctly.
- Besi Iliyopotoshwa au Isiyoeleweka:
- Reduce the subwoofer's volume level.
- Adjust the crossover frequency to ensure it blends smoothly with your main speakers.
- Experiment with the phase switch (0°/180°) to find the setting that provides the clearest and most impactful bass.
- Angalia miunganisho yoyote iliyolegea au nyaya zilizoharibika.
- Ensure the subwoofer is not placed too close to walls or corners, which can cause excessive booming.
Vipimo
| Kipengele | Vipimo |
|---|---|
| Transducer ya Mzunguko wa Chini | 10" (250mm) PolyPlas™ cone, cast frame |
| Amplifier Nguvu | 300 watts RMS; 500 watts peak |
| Majibu ya Mara kwa mara | 27Hz - 150kHz (-3dB) |
| Mzunguko wa Crossover | 50Hz – 150Hz (variable), 24dB/octave |
| Aina ya Uzio | Imetiwa muhuri |
| Power Requirement (US) | 120V, 60Hz |
| Power Requirement (EU) | 220V - 230V, 50Hz / 60Hz |
| Matumizi ya Umeme (Hatari) | <6W (120V), <0.55W (230V) |
| Matumizi ya Nguvu (Upeo wa Juu) | 360W / 3.8A (120V), 395W / 2.1A (230V) |
| Vipimo (H x W x D) | 17-1/2" x 14-29/32" x 14-31/32" (444mm x 379mm x 380mm) |
| Uzito | Milioni 50 (23kg) |
| Aina ya Kuweka | Sakafu imesimama |
| Nyenzo | Mbao |
| Aina ya Spika | Subwoofer |
| Kipengele Maalum | Bass Kuongeza |
| Vifaa Sambamba | Smartphone, Tablet, MP3 Player, Desktop, Television, Projector, Laptop |
| Kipenyo cha Subwoofer | Inchi 10 |
| Usanidi wa Idhaa ya Sauti inayozunguka | 5.1 |
| Rangi | Nyeusi |
| Impedans | 8 ohm |
| Teknolojia ya Uunganisho | RCA |
| Njia ya Pato la Sauti | Mzunguko |
| Uingizaji Voltage | 120 Volts |
Udhamini na Msaada
The JBL Studio 550P 10-Inch Powered Subwoofer comes with a Udhamini mdogo. For detailed information regarding warranty coverage, terms, and conditions, please refer to the warranty card included with your product or visit the official JBL website. For technical support, service, or any inquiries not covered in this manual, please contact JBL customer support through their official channels.
