Mwongozo wa Maelekezo Muhimu ya Programu ya AKO D14918

 

D149H181 Ed.08

AKO-D14918

The AKO-D14918 programming key allows you to quickly and easily copy configured settings from one controller to another with the same functionality

Maonyo

-Using the equipment without following the manufacturer’s instructions may affect the device’s safety requirements.
-The unit must be used in a location protected from vibrations, water and corrosive gases, where the ambient temperature does not exceed that shown in the technical data.
-Connecting this key to unsupported devices (see table) can cause serious damage to both pieces of equipment.
-In equipment with active communication, log out of communications software or disconnect the cable before connecting the programming key. The communication controller’s address must be 1.

Maelezo

1. LED COM
2. UFUNGUO WA REKODI
3. EXTERNAL POWER CONNECTOR
4. READ KEY
5. LED ILIYO
6. CABLE YA KIUNGANISHI

Utangamano

Refer to the instruction manual of your equipment on its compatibility with the AKO-D14918 programming key.

Connecting incompatible devices can permanently damage the key.

Wiring

1. MUHIMU: Pay attention to the orientation of the connector.
2. AKO-80018 
   (Si lazima)
3. AKO-D14918

Ugavi wa nguvu

-If the controller is in operation (on-site programming), the key does not require an external power supply (it is powered via the connecting cable).
-If the controller is NOT powered (workshop programming), the key requires a 12Vdc/500 mA external power supply (AKO-80018 or equivalent).

Uendeshaji

MUHIMU: After connecting the key to the equipment wait for 5 seconds before starting the reading or writing process.

RECORD key

Write the data contained in the key memory to the controller.
Keep the key pressed until the COM led starts flashing quickly.
When recording is complete the controller will reset.

READ key

It reads the data from the controller and stores them in the programming key.
Keep the key pressed until the COM led starts flashing quickly.
When recording is complete the controller will reset.

LED ILIYO

Steady or flashing: Indicates that the key is connected to the controller.

LED COM

Imara: Indicates an error in the transmission/reception of data
Kuangaza haraka: Indicates transmission/reception of data in progress. At the end of the transmission LED COM itazima.
Kumulika polepole: Indicates compatibility error- the data contained in the memory of the key is not compatible with the model of controller connected. Data can only be read from the controller to the key.

KUMBUKA: To restart after a transmission or compatibility error, turn off the power supply or disconnect the controller connector cable.

MUHIMU: Kamwe disconnect the programming key during data transmission.

Vipimo vya kiufundi

Length of cable from programming key to controller . . . . . . . . . . . . . 300 mm
Ugavi voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Vdc nominal
Supply current . . . . . . . . . . . . . . . . . . . . . . . . . . . . AKO-80018 / 500 mA máx.
Vigezo vya mazingira:
Ambient working temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . 0ºC to 50ºC
Storage temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -30ºC to 70ºC

AKO ELECTROMECÁNICA, SA
Av. Roquetes, 30-38 | 08812 Sant Pere de Ribes | Barcelona | Kihispania

35D149181 REV.07 2025

Tunahifadhi haki ya kutoa nyenzo ambazo zinaweza kutofautiana kidogo kwa zile zilizofafanuliwa katika Laha zetu za Kiufundi.
Habari iliyosasishwa inapatikana kwenye yetu webtovuti.

Nyaraka / Rasilimali

AKO D14918 Programming Key [pdf] Mwongozo wa Maelekezo AKO-D14918, AKO-80018, D14918 Programming Key, Programming Key, Key

Marejeleo

• Mwongozo wa Mtumiaji